玻璃門安裝相比其他材質門安裝更為復雜，玻璃門安裝工程要十分小心和注意，這樣可以有效的避免造成一些不必要的傷害。下面來講講濟南玻璃門安裝前準備工作以及安裝施工事項吧。

The installation of glass doors is more complicated than that of other materials. The installation of glass doors should be very careful and careful, which can effectively avoid causing unnecessary injuries. Now let's talk about the preparatory work before the installation of Jinan glass doors and the installation and construction matters.

安裝前準備工作

Preparation before installation

玻璃門安裝前，保證地面施工已完畢，不銹鋼或其它飾面門框已完畢。厚玻璃限位槽已留出。一定要非常小心四個角位的倒角一通常情況應用手握細砂輪塊，緩慢進行磨角，以防崩邊崩角。不銹鋼飾面的木底托，應用木楔釘?shù)姆椒ü潭ㄔ诘孛妗Ｖ罂捎?**膠將不銹鋼飾面板粘卡在木方上。鋁合金方管可用鋁角固定在框柱上，或用木螺釘固定于地面埋入的木楔上。

Before the installation of glass doors, ensure that the ground construction has been completed and the stainless steel or other decorative door frames have been completed. Thick glass limit groove has been reserved. Be very careful with the chamfering of the four corners. Generally, hold the fine grinding wheel and grind the corners slowly to prevent edge collapse. The wooden bottom bracket with stainless steel facing shall be fixed on the ground by means of wood wedge nails. After that, the stainless steel decorative panel can be stuck on the wooden square with universal glue. The aluminum alloy square tube can be fixed on the frame column with aluminum angle, or fixed on the wood wedge embedded in the ground with wood screws.

安裝施工

Installation construction

先用玻璃吸盤器把厚玻璃吸緊，再手握吸盤器把厚玻璃板抬起。抬起時需要2－3人同時進行。抬起后的厚玻璃板，插入門框頂部的限位槽內，再放到底托上，并對好安裝位置，使厚玻璃板的邊部，正好封住側框柱的不銹鋼飾面對縫口。

First, use the glass sucker to hold the thick glass tightly, and then hold the sucker to lift the thick glass plate. Two to three people are required to lift at the same time. After lifting the thick glass plate, insert it into the limit slot at the top of the door frame first, then place it on the bottom bracket, and align the installation position so that the edge of the thick glass plate can just seal the stainless steel facing seam of the side frame column.

先將玻璃膠打開裝入玻璃膠注射槍，再用玻璃膠槍的后壓桿端頭板，這樣便可頂住玻璃膠罐的底部。用手托住玻璃膠注射槍身一只手握著注膠壓柄，并不斷松、壓循環(huán)地操作壓柄，擠出少量的玻璃膠注入。再把玻璃膠的注口對準縫隙端封口。

First open the glass glue and load it into the glass glue injection gun, and then use the rear pressing rod end plate of the glass glue gun to support the bottom of the glass glue tank. Hold the glass glue injection gun body with one hand and hold the glue injection handle, and operate the handle continuously and cyclically to squeeze out a small amount of glass glue injection. Then align the injection of glass glue with the gap end for sealing.

固定部分的厚玻璃板，往往不可用一塊來完成。在厚玻璃對接時，注意對接縫隙要在2-3mm之間，厚玻璃邊需倒角。兩塊相接的厚玻璃定位并固定后，用玻璃膠注入縫隙中，注滿之后用塑料片在厚玻璃的兩面刮平玻璃膠，用凈布擦去膠跡。

The fixed part of the thick glass plate can not be completed by one piece. During butt joint of thick glass, the butt joint gap shall be 2-3mm, and the thick glass edge shall be chamfered. After the two thick glasses connected are positioned and fixed, the glass glue is injected into the gap. After filling, the plastic sheet is used to scrape the glass glue on both sides of the thick glass, and the glue mark is wiped off with a clean cloth.

消費者在選擇玻璃門的時侯也有一些方法，不但要掌握方法，還需要注意安裝過程中出現(xiàn)的問題，如果不知道自己裝修以后是什么效果，那么可以通過選擇玻璃門圖片來完成，這樣就可以得到很多的優(yōu)勢。更多相關事項就來我們網(wǎng)站http://radiefmail.com進行咨詢吧！

Consumers also have some methods when choosing glass doors. They should not only master the methods, but also pay attention to the problems in the installation process. If they do not know what the effect is after their own decoration, they can choose the pictures of glass doors to complete, so they can get a lot of advantages. Come to our website for more information http://radiefmail.com Consult!